פורום חשמל
- לנושא זה 13 תגובות,2 משתתפים, והוא עודכן לאחרונה לפני 7 שנים, 5 חודשים על ידי- arielsegal.
-
מאתתגובות
-
4 בדצמבר 2016 בשעה 21:05 #96728mastaq91משתתף
האם יש התקן, מכשיר ששומר על סדר פאזות ביציא, ללא קשר לשינוי סדר פאזות בכניסה?
התברר, להפתעתי (למרות המכשירים וממסרים רבים שהמציאו ) לא קיים. יש מכשירי לבדיקה סדר פאזות, יש ממסרים להתראה ואפילו להפסקה הזנת חשמל במקרה הסדר לא נכון. אבל אין מכשיר סדרתי שאוטומטי שומר על סדר. אבל מה אם צריך לספק את סדר הנכון?
חשבנו על זה. ניתן לבצע. ואם לבנות, אז לשלב עם עוד פונקציות. לדוגמה הגנה על חוסר פאזה, חוסר אפס, חוסר הארקה
הדבר שימושי עבור מתקנים ניידים, אולי גם לאל-פסק. כעת רוצים לנסות
5 בדצמבר 2016 בשעה 8:00 #96732arielsegalמנהל בפורוםהיי מיכאל.
לא מכיר מכשיר סטנדרטי כזה אבל קל מאוד ליצר.
אם משתמשים במד סדר פזות תקני יש לו 2 נורות. אחת לסדר נכון ושניה לסדר הפוך.
ניתן להפעיל את המתקן רק אם נורית סדר נכון פועלת.
5 בדצמבר 2016 בשעה 17:06 #96741mastaq91משתתףאריאל
לא רוצה להתחכם
אבל לא על זה דיברתי
אמרתי על דבר שמאפשר להפעיל את המתקן תמיד ואוטומטי בסדר פאזות הנכון, לא תלוי מהחלפת סדר פאזות בכניסה (תמיד מקבלים סדר פאזות הרצוי)
(אחרת לא הייתי פותח דיון בפורום מכובד כזה)
לא תמיד בשטח עם מתקן נייד יש חשמלאי להחליף פאזה ולא תמיד קל לזהות שפזא הפוכה
אבל גם דבר כזה מאוד לייצר ושאמרתי להוסיף כל מני הגנות
5 בדצמבר 2016 בשעה 20:44 #96750arielsegalמנהל בפורוםנשמע מעניין מאוד מיכאל.
כמו הרבה רעיונות טובים ומעניינים שאתה מעלה כאן.
תבורך
5 בדצמבר 2016 בשעה 21:14 #96754mastaq91משתתףכך לא מעניין
חשבתי לשמוע התנגדויות, הצעות, שאלות. זאת הדרך לחדשנות
5 בדצמבר 2016 בשעה 21:19 #96755arielsegalמנהל בפורוםלא נראה שזו בעיה טכנית משמעותית.
יש לדעתי להתקין התקן שבודק סדר פזות ואם הסדר אינו נכון להצליב 2 .
5 בדצמבר 2016 בשעה 21:38 #96757mastaq91משתתףאז למה לא קיים
הדבר שימושי וחיוני לדוגמה לכל מתקן חיוני נייד (מיזוג, צילרים, גנראטואים, לוחות וכו’)
6 בדצמבר 2016 בשעה 17:25 #96768mastaq91משתתףהיו כמה גרסאות
בחרנו את זה
לא רק שומר תמיד על סדר פאזות אבל גם הגנה נגד:
- עליה מתח
- ירידה מתח
- ניתוק פאזה או אפס
- השאה (כדי לא להכניס מתח לא תקין)
- אפשרות הפעלה על-ידי מפסק פיקוד מרחוק
כל זה ניתן לבצע בעזרת 2 ממסרי מתח ו2 מגענים
7 בדצמבר 2016 בשעה 15:18 #96778arielsegalמנהל בפורוםיופי של פתרון!!! 😀
לא הבנתי את מה שכתבת שזה שומר מפני עליה וירידה של מתח
7 בדצמבר 2016 בשעה 17:13 #96780mastaq91משתתףאם ניקח ממסר כזה, לדוגמה
-
Control of three-phase four-wire voltage net with neutral*
-
(Overvoltage control at any phase from 240V to 295V (switch, 10 positions*
-
(Undervoltage control at any phase from 165V to 220V (switch, 10 positions*
-
Control of alternation phases*
-
Control of break phases*
-
Control of “stiking” phases*
-
Operation delay from 0,1 to 10s
PURPOSE OF THE RELAYRelay control voltage RKN-3-15-15 is designed to control the availability, “sticking” and order of alternation of phasesin three-phase circuits of voltage in net with neutral, and for the control of undervoltage and overvoltage above and below the set threshold.DESIGN OF THE RELAYRelay is produced in a plastic case with a unified front connection wires power and switched circuits. Mounting is carried out on a DIN rail width 35mm or on a smooth surface. To set on a smooth surface, you need to push locks. Terminal design provides robust clamp wires up to 2,5mm<sup>2</sup>. On the front panel there are two switches to set upper “U<sub>phase</sub>>” and lower “U<sub>phase</sub><” thresholds, regulator of actuation time “t”, two red indicators of net error “U>”, “U<“, yellow indicator of built-in executive relay ““, three red indicators of availability phases “L1”, “L2”, “L3”.OPERATION OF THE RELAYThe relay is powered by controlled net. For this you need to connect three controlled phases to terminals L1, L2, L3,neutral wire to terminal N.WARNING: A connection the neutral wire to terminal N is must!Upper “U<sub>phase</sub>>” and lower “U<sub>phase</sub><” thresholds are setting by using potentiometers, that located on the front panel.A delay of actuation relay is exhibited by medium potentiometer. When power is applied, if a delay is setted and all controlled parameters are normal, the relay will turn on at the end of the counting delay time t, and relay contacts 11-12, 21-22 will be open and contacts 11-14, 21-24 will be close. A flashing indicator “” signals about the counting time delay actuation at which the end of it the buil-in relay switches. At a deviation of one of the parameters of the nominal value, turn on the indication of error and relay switches off after the end of delay. Upon returningthe controlled parameter to normal, the indication of error is switched off immediately, and the relay switches after the end of actuation delay. At loss of all three phases a relay turns off without counting delay of actuation time set the user.WARNING: In violation an order of alternation phases the is a brief alternating turning on indicators «U>», «U<».Status of indicators «L1», «L2», «L3»:-
In case of availability of all phases all three indicators turns on
-
In the absence of any phase will turn off the appropriate indicator «L1», «L2», «L3».
-
When the neutral wire breaks, indicators «L1», «L2», «L3» have little noticeable glow and indicators «U>», «U<», «» is turned off.
-
When you connect the neutral wire to one of the terminals «L» for connection of phase, and phase to terminal «N»,turns off the appropriate indicator «L1», «L2», «L3», indicators «U>», «U <» will be turned on.
אני באמת רוצה לעשות פיילוט עבור יח’ מיזוג לחירום פקע”ר
לכן, אשמח לקבל המלצות או שינוים7 בדצמבר 2016 בשעה 17:17 #96781mastaq91משתתףאריאל
הממסר הוא לא היה בכותרת, אבל שאלת
ממסרים מזוג הזה בעצמם דבר יפה
המחיר, אגב כ- 100 ש”ח
8 בדצמבר 2016 בשעה 7:44 #96787arielsegalמנהל בפורוםתודה רבה.
שאפו גדול
8 בדצמבר 2016 בשעה 8:53 #96789mastaq91משתתףאז נתחיל לייצר כמכיר סטנדרתי?
9 בדצמבר 2016 בשעה 16:25 #96799arielsegalמנהל בפורוםמתאים.
נבנה אב טיפוס ולעבודה.
-
מאתתגובות
- יש להתחבר למערכת על מנת להגיב.